Articles
2008
February 2008: "Automating the Tests in IEC 60601-1"
by Shari Richardson, QuadTech Director of Engineering, Medical Division
As seen in the February issue of Conformity
2007
August 2007: "What's New in EMC Standards for Medical Devices"
by Robert M. Brown, QuadTech VP Technical Operations
James Conrad and Frank O'Brien
As seen in the August issue of Conformity
June 2007: "Leakage-Current Testing for Patient-Monitoring Devices"
by Jeffrey St. Onge, Chief Engineer for Medical Division, QuadTech
As seen in the June issue of Medical Device & Diagnostic Industry (MD&DI)
2006
June 2006: "Choosing the Right Current for Ground Bond Testing"
by Tracey Gilpin, Technical Writer, QuadTech
As seen in the June issue of Conformity Magazine
March 2006: Focus On..."Test Equipment - Choosing a Hipot Tester"
by Tracey Gilpin, Technical Writer, QuadTech
As seen in the March issue of Conformity Magazine
January 2006: "Verification of Electrical Safety Testers"
by Robert Brown, QuadTech's Director of Products
As seen in the January issue of Conformity Magazine
2005
November 2005: "Purchasing an Electrical Safety Tester"
by Shari Richardson, QuadTech's Application Engineer
As seen in the November issue of Conformity Magazine
October 2005: "Ground Bond Testing vs. Ground Continuity Testing: What is the Difference and Why Choose One Over the Other?"
by Shari Richardson, QuadTech's Application Engineer
As seen in the October IEEE Newsletter
February 2005: "A Regulatory Review of the EMC Standard for Medical Devices"
Co-authored by Robert Brown, QuadTech's Director of Products
As seen in the February issue of Compliance Engineering Magazine
2004
July 2004: "Leakage Current Standards Simplified"
Co-authored by Robert Brown, QuadTech's Director of Products
As seen in the July issue of MD&DI
May 2004: "IEC 60601-1: Medical Device Marking and Labeling"
Co-authored by Robert Brown, QuadTech's Director of Products
As seen in the May issue of MD&DI
April 2004: "National Deviations to IEC 60601-1."
"Understanding specific national requirements is critical to developing a test plan."
Co-authored by Robert Brown, QuadTech's Director of Products
As seen in the April issue of MD&DI
2003
September 2003: "A Primer for IEC 60601-1 "
co-authored by Robert Brown, QuadTech's Director of Products
As seen in the September issue of MD&DI
July 2003: "Testing Equipment: Appliances on Trial"
As seen in the July issue of Appliance Magazine
May 2003: "The C's and D's of dielectric measurements"
by Jim Richards, Applications Engineer, QuadTech
As seen in the May issue of Test & Measurement World Magazine
2002
October 2002: "Automating Complex Electrical Safety Testing of Medical Devices"
by Jim Richards, Applications Engineer, QuadTech
As seen in the October issue of Medical Electronic Manufacturing
May 2002: "Medical Electronics: Ensuring Compliance with Product Safety"
by Jim Richards, Applications Engineer, QuadTech
As seen in the May issue of Compliance Engineering
2000
November 2000: "Minimize Measurement Errors in Component Test Fixtures"
by Robert Brown, QuadTech's Director of Products
As seen in the November Issue of Test and Measurement World
September 2000: ElectronicsWeb.com: Custom Design Your Own Shock Therapy
by Tracey S. Gilpin, Technical Writer, QuadTech Inc, Maynard, MA
July 2000: Electronic Products: Some Basic Considerations in Inductance Measurements
by Tracey S. Gilpin, Technical Writer, QuadTech Inc, Maynard, MA
June 2000: Test and Measurement.com: What's Your Real (or Imaginary) LCR IQ?
by Tracey S. Gilpin, Technical Writer, QuadTech Inc, Maynard, MA
1999
April 1999: Electronic Products: Choosing a hipot tester depends on the level of test
by Jim Richards, Applications Engineer, QuadTech
1997
July 1997: "Ensuring RH Sensor Repeatability with Capacitance Testing"
by Robert Brown, QuadTech's Director of Products
As seen in Sensors Magazine |
